• Great for the removal of rubber hoses from inlets, outlets and clamps.
• Specially designed end makes hose removal easy.
• Hardened and plated shaft anchored in large, comfortable handle. 8½” overall length with 4” exposed shaft.

• Makes accurate, straight cuts with clean edges on rubber or plastic hose, PVC pipe and certain types of wire and wire cable
• Handles up to 1 1/8" O.D. material
• For automotive, autobody, marine and aviation shop.

• Designed for the technician who must kneel at times to complete repair and service work. Thick foam padding takes the pain out of kneeling on hard surfaces. Lightweight and flexible, these knee pads provide comfort in a durable construction. Hard plastic caps make swiveling effortless and assure long life of pad. Easy to fasten with adjustable Velcro straps. Sold as a set of two.

• For sheet metal and other thin materials up to 1/8” thick.
• Has 13 hole sizes in 1/32” increments from 1/8” thru 1/2”. High speed steel with titanium coating for longer life. No slip shank fits all 1/4” drills.

• Made of high speed steel for sheet metal. Have with 135 degree split points for fast drilling without center punching. Packed 10 drill bits in a hang-up plastic display vial.

• Cuts steel, aluminum, brass, copper, & plastic sheet or tubing without distortion. Makes curved or straight cuts. Will cut steel wire and electrical wire with ease.
• Replacement Blades Available

• True Technician's aids! Use to remove paint, carbon, rust, corrosion, and weld scale. Excellent for body surface preparation. Made with 0.020" high fatigue resistant steel wire. ¼" shank fits all portable drills. For best brushing results do not operate over 8,000 RPM Maximum safe speed 20,000 RPM.

• True Technician's aids! Removes carbon from cylinder heads, valve ports and pistons quickly. Made of crimped steel wire. ¼" shank fits all portable drills. For best brushing results do not operate over 8,000 RPM Maximum safe speed 20,000 RPM.

• True Technician's aids! Use in severe applications to remove deep rust, weld splatter, scale and heavy carbon deposits. Made of crimped steel wire. ¼" shank fits all portable drills. For best brushing results do not operate over 8,000 RPM Maximum safe speed 20,000 RPM.

• Made of fatigue resistant, .014" crimped steel wire. This brush is used for numerous auto body and engine applications. Removes paint, carbon, rust and corrosion. Cleans pitted surfaces and gasket residue. Has ¼" shank and fits all electric drills. Maximum safe speed 5,000 RPM.

• Contains one Each of the most popular brushes - brass, nylon, and stainless steel bristles. Use the brass and stainless steel brushes where aggressive action is needed. The nylon brush is used for milder cleaning action. Polypropylene handles have been molded for easy gripping. Specially designed narrow head fits into hard to clean areas. Each brush is 3x7 rows and has a hang up hole in the handle. For use with cleaning solvents, thinners, and chemicals. Excellent set for all types of cleaning applications. Overall length of Each brush is 7".

• An excellent aid for all technicians. Wire bristles are encapsulated in a special material to extend brush life and promote aggressive brush action. Quickly gets down to bare metal. Great for use in confined areas and for removing paint before spot welding. Fits any ¼" drill. Maximum safe speed 18,000 RPM.

• Fits all 5 and 6 gallon pails. Easily dispenses fluid with lift action. For use with all non-corrosive liquids. Seals designed for use with thinner. Fully plated, steel construction. Dependable and long lasting.
• Click here to go to reducers page

• Lift action handle dispenses approximately 1 ½ pints per complete stroke. Adjustable suction tube fits 15, 30, & 50 gallon drums. For petroleum based fluids such as lubricants, anti-freeze, solvents, thinners, and other non-corrosive liquids. Discharge spout is removable. Bung adapter fits all standard drum. Plated steel construction.
• Click here to go to reducers page

 A B C

• Quickly removes spot welds holding sheet metal. Can also cut small access holes in sheet metal. Has double ended 3/8" blade and ¼" arbor with retractable pilot. When one side of blade becomes dull turn blade 180° for fresh cutting surface. Blades interchange with other spot weld arbors. Arbor fits all ¼" drills.
• 3 PK. REPLACEMENT BLADES
• MAINTENANCE KIT CONSIST OF 3 PILOT PINS & SPRINGS

• Narrow profile can easily access limited and hard to reach areas
• Strips 22-12 gauge single or multiple stranded conductor wire
• Automatically adjusts to wire size
• Adjustable strip length gauge
• Built in wire cutter.
• Easy grip handle

• 2 ¼" nose reaches for standard use. These riveters can handle the toughest riveting jobs. The 17" long handles give you the leverage to effortlessly set five sizes of aluminum and steel rivets: 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (6.0mm), and ¼" (6.4mm). All metal construction, simple design and few moving parts ensure years of hard working use. Comfortable vinyl hand grips. Nosepieces thread into handles for convenient storage.
• Replaces the original nose on the Cat. No. 19250, Super Duty Riveter. Installs quickly and easily. With the new nose length of 5 ¾", this riveter easily reaches into recesses such as grilles, bumpers, and window regulators.

• 5 ¾" nose reaches to access deep recesses such as grilles, bumpers, and windows regulators. These riveters can handle the toughest riveting jobs. The 17" long handles give you the leverage to effortlessly set five sizes of aluminum and steel rivets: 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (6.0mm), and ¼" (6.4mm). All metal construction, simple design and few moving parts ensure years of hard working use. Comfortable vinyl hand grips. Nosepieces thread into handles for convenient storage.

• Ingenious device prevents stabbing your finger - a must for every technician!
• Quickly & easily guides the pick point of most circuit testers into the center of all primary automotive electrical wire.
• Holds the circuit tester in position allowing technician to work with both hands free
• Impervious to gasoline & oil

• The most computer safe circuit tester!
• High impedance - the current draw is less than 7 milliamps
• Quickly and safely tests high and low voltages (power and ground) on all vehicle circuits, including computerized engine and body controls
• Dual color LED indicates red for power (high) and green for ground (low) on 6, 12 and 24 volt systems.

• Fits all spark plug holes. test for maximum compression on foreign & domestic model gas engines. Quick type gives instant reading. Duel gauge reads both Metric and English units.  Do Not Use On Diesel Engines.

• Excellent Quality, Popularly Priced! A great combination of the chisels most often used by automotive & auto body technicians. Made to exacting Tool Aid standards from alloy steel with .401" Parker shanks and covered by our "no questions asked" warranty. Packaged in see-through vinyl pouches.
• 8 DIFFERENT STYLES TO CHOOSE FROM.

• High quality at low cost! This is the best tool value, designed to do the job in every shop and garage. Features shafts of one piece forged construction with rolled threads. ½" square socket head makes tool usable with ½" ratchet drive. Outside hex fits 15/16" socket. Use socket extension if space is tight. Save time and money when strut body must be removed or replaced and coil spring is reused. Each tool contains safety kit and illustrated instructions.

• A basic set of the most popular Slugger hooks supplied in a carton without board or metal box. Allows new technician to get started with a quality set at significant savings. Additional Slugger parts can be added to set in the future.

• 8 BIG FEATURES
• 10lb slide weight designed for in-line impact. Balanced for continued use without fatigue.
• Special hand-fit weight for ease for work.
• The most complete set available! 10 of the latest and most modern engineered body pulling and pushing attachments.
• Consists of 16 different parts.
• Dual hammer action for reverse or direct reconstruction blows.
• Quick assembly for applied hook-ups on fender edges, bumper ends, rocker panels, aligning doors and door edges, hoods and hood hinges, truck and truck hinges, headlights and many more applications.
• Rubberized hand-hold for good grip and safety.
• All parts easily stored on permanent board.
• Supplied with exclusive lock nut to keep attachments from rotating.

• An assortment of the most widely used Slugger pulling and pushing attachments packed in a handy metal box
• 10 lb. Slide weight designed for in-line impact
• Quick assembly for applied hook-ups on fender edges, bumper ends, rocker panels, aligning doors and door edges, hoods and hood hinges, trunk and trunk hinges, headlights and many more applications.

• 5lb slide weight on plated, solid 5/8" shaft. Cushioned vinyl grip, broached nose cone, puller screw extra long, body hook of aircraft steel. Nose cone & shaft threads are 5/8" - 18.

• 3lb slide weight on plated steel shaft. Blue vinyl hand grip provides 100% grip. Broached hex in nose cone lock pulling screw in place ..ends breakage. 2 hardened pulling screws & "L" puller hook fabricated of aircraft quality steel. Nose cone & shaft threads are 1/2" - 20.

• Heavy duty slide hammer with 3lb weight. Vinyl hand grip. Wide aircraft steel body hook. "L" hook, broached nose cone, 2 jam nuts and 2 hardened pulling screws. Nose cone & shaft threads are ½" - 20.

• Use to pull out sheet metal panel dents on doors, fenders and hoods. Steel handle and reinforced steel support plate allow for maximum pull. Release suction easily by lifting "lipped" edge.

• This inexpensive, high performance, hot air source that delivers concentrated, heated air to the job. Use in auto body, automotive, industrial, marine, home, farm, and numerous other applications. Has two heat selections: 750°F and 1000°F. Only weighs 1.2 pounds. Operates on 120 volts, 10 amps, 1,200 watts. Contains no asbestos. U.L. and CSA listed. Full instructions provided for most all applications.

• For windshield removal and replacement. Use to pull out sheet metal panel dents on doors, fenders and hoods. Easy to use – Just firmly set the suction cup and squeeze the handles together. Suction Cup measures 4 5/8” diameter. Capacity 80 lbs.

• For windshield removal and replacement. Easy to use – Just firmly set the suction cup and press down on each lever. Suction Cups measure 4 5/8” diameter and pivot for better gripping. Capacity 154 lbs.

• Use to remove windshields, backlights, and bonded backlights. Cuts the sealant around windows with specially designed tempered steel blade. Includes both the knife for cutting and a wire pull type remover with t-handles.

• Instant removal of door handle and window regulator clips.
• End damage to upholstery and escutcheon plate.
• Standard for all Ford, General Motors and American Motors models amoung others.

• Remove the plastic trim pad fasteners used on General Motors cars since the early 1970`s.
• Does not damage trim pad or fasteners.
• They can be fully reused.
• The tool reaches under the trim panel and pries against hidden surfaces without breakage or scratching paint.
• Works equally as well on metal trim pad fasteners used on Ford, Chrysler and other cars.

• Remove clips holding windshield and rear window reveal molding. Double side tool can be applied easily and allows for quick disengagement of molding clips. Rubber insert on tools protects glass from being scratched. Made from heat treated spring steel. A must for body and glass shops.

• It only takes a few seconds to easily and safely remove upholstery and trim clips on doors, dashboards and consoles Does not mar panel surface Universal design removes both plastic and metal clips of various shapes and sizes Eliminates broken fasteners 9" overall length.

• Used to remove windshield with a curved angle found in many newer cars. Cuts the urethane bond holding windshield. Light-weight, rigid aluminum shank with vinyl grip.

• Use to remove windshields, backlights, and bonded backlights. Cuts the sealant around windows with specially designed tempered steel blade. 1 Extra blade supplied with each tool. Pull handle provides additional leverage.
• REPLACEMENT BLADES AVAILABLE

• Every body technician uses this dolly for bumping, straightening, dinging, and finishing various portions of body, door panels, and fenders. Good variety of curves and angles, with two beading and flanging lips. Made of drop-forged steel.

• This large drop-forged steel model remains popular with body technicians. It has flat and low crown areas and is used in dinging flat surfaces and lower portions of hood. Good for close work. Made of drop-forged steel.

• A useful drop-forged steel dolly for work behind brackets, braces and other reinforcements on roof, body, fenders, and panels. Advantageous in modern body design. Easy to hold in difficult areas.

• Popular for use in sharp corners and wide radii portions of panels and body. Made of drop-forged steel.

• The most popular body repair specialty tool. Combines all the contours and weight of a dolly with the reach and maneuverability of a spoon. Use for forming, prying and caulking in those hard to reach places.

• Most popular body shop hammer. Designed to provide excellent balance for close-in work and finishing. Flat, round face, 1-1/4" dia. Pencil point on 5-1/4" drop-forged steel body.

• Good for close work and final finishing. Both faces flat. Round face 1 3/8" dia. Square face 1 3/16". Overall 4 1/4". Drop-forged steel.

• Use for small clearance jobs and low spots in high crown panels, as well as general finishing work. Round face 1 1/2" dia. Bullet point on 5 3/4" body. Drop-forged steel.

• For all-around work and fast finishing. Will not stretch metal. Ideal for close quarters. Drop-forged steel body 5" overall. Round head has uniform serrated face 1 5/8" dia. Square head is flat faced 1 9/16". Drop-forged steel.

• This drop-forged steel hammer is a must for straight finishing and grooving jobs. Work on narrow fender beads with wedge shaped chisel cross peen. Round head has flat surface 1-3/8" dia. 5-1/2" overall length. Drop-forged steel.

• Very popular, reliable, drop-forged steel unit. Excellent for heavy gage truck fenders and panels. Well balanced, hit with confidence! Flat round face 1 1/2" dia. Flat, square face 1 1/2". Overall length 5".

• Drop-forged steel unit provides long reach to inaccessible or otherwise blocked areas. Has round, flat face 1 7/8" dia. Pick finished to pencil point. Overall length is 8".

• Long gentle curve reaches behind inner construction between panels which are close together for removal of dents and bumps. Use for molding panels and beadings. 15" overall length.
   

• Use for slapping and surface metal finishing on fenders, quarter panels and trunk lids where blow is spread over full impact area. 15" overall length.

• Use inside where maximum curvature of damaged sheet metal is to be repaired. Excellent for prying out dents in narrow, curved spaces. 15" overall length.

• 3 Tools in 1! Combines high crown spoon with general purpose surface. Unique length provides leverage for prying and extra long reach. 27" overall length.

• A handy aid for the body technician. Hit ridges directly or transfer blow with hammer. Flat surface absorbs and distributes blow evenly. Smoothes out ridges uniformly without marring surface. Made of drop-forged steel.

• Stick-It / PSA Flexible, round, palm sander fits comfortably in hand.
• Use with 6" sandpaper.
• Contours to flat or curved surfaces.
• When sander is turned 90° there is a new grit surface.
• Click here to go to 6" Stick - it Sandpaper

• Velcro / Hook-it / Hook & loop Flexible, round, palm sander fits comfortably in hand.
• Use with 6" sandpaper.
• Contours to flat or curved surfaces.
• When sander is turned 90° there is a new grit surface.
• Click here to go to 6" Hook-It Sandpaper

• Specially designed holding slot grips sandpaper firmly to reduce slipping and tearing
• Flexible, Air File sanding board with foam pad. Both wooden grips fit comfortably in hand.
• Use with Air File Clip On sandpaper.
• Contours to most flat and / or curved surfaces.
• Click here to go to Air File Clip-On Sandpaper

• For patching sheet metal panels uniformly and quickly.
• Forms a step around the area to be repaired.
• Patch is placed on flange of step, flush with original panel surface.

• A complete size range of phenolic reinforced backing plates for sanding and grinding work.
• These disks are designed to be lightweight and provide desired flexibility for sanding.
• If additional rigidity is required, combine 2 or 3 together.
• Each plate has the same molded depressed center contour and 7/8" ID hole.
• Maximum safe eye and face protection for this type of work.
• Maximum safe speed is 6,000 RPM.
• Available in combination packs

• (5/8 - 11 Thread) Fits most vertical and angled polishers. Hex Spindle Nut specially designed to make installation and removal old Backing Pad fast and easy. Molded of flexible, durable rubber. 7" diameter pad supplied with 5\8"-11 hex spindle nut. Maximum speed 5,000 RPM

• Allows any die grinder or drill to be turned into a cut-off tool using either 1\4" or 3\8" I.D. Cut-Off Wheels. Cutting tools should have safety guard. Always wear eye and face protection.